Do You Know Your Power to Weight Ratio?
Published at 26 Jun 2019

Using cycling as an example, we take a look at the performance relationship between outright power and power-to-weight ratio, and how to get better when the terrain point upwards…

 

 

As much as many athletes would like to, it’s not possible to buy more power (well, not legally anyway). To enable the muscles to produce more power, you have to perform specific training sessions such as interval training over an extended period of time, which requires significant effort and commitment. And while improving your endurance fitness can significantly increase the amount of power your muscles can produce, basic human physiology means there’s a limit to the gains that can be achieved this way.

Fortunately however, the absolute amount of power at your disposal is not the only factor for determining performance. The amount of mass you have to move around – ie your bodyweight – is vitally important too. This is because accelerating mass or moving mass uphill against the force of gravity requires power. It follows therefore that if you have less mass to lug around, you need less power to move it against gravity – a concept which leads to the notion of ‘power-to-weight ratio’.

Cycling, Power & Weight

Power-to-weight ratio is an important determinant of performance in a range of sport where athletes work against gravity – for example X-country skiers, runners and in fact any sport which involves running. That’s because each stride taken when running involves an ‘up and down’ motion, requiring the muscles to work against and overcome the force of gravity. However, nowhere is the relationship between power and power-to-weight ratio more important than in the sport of cycling.

For most cyclists who don’t ride on perfectly flat and smooth roads (ie virtually every road and off-road cyclist), what matters just as much as maximum power output is the amount of power that can be produced in relation to bodyweight – ‘power-to-weight ratio’ – usually expressed in watts per kilogram.

Working Out a Power to Weight Ratio

To work out a power-to weight ratio figure, simply divide your maximum sustainable power output (in watts) by your body mass in kilograms (kg). For example, an 80kg rider with a maximum sustainable power output of 280 watts has a power-to-weight ratio of 3.5 watts per kilo (commonly abbreviated as 3.5W/kg or 3.5W.kg-1).

Why Does It Matter?

Power-to-weight ratio matters because it’s a great predictor of performance. Take two cyclists; cyclist A can sustain a maximum power output of 250 watts while cyclist B can only manage 225 watts. On a perfectly flat, smooth indoor track (where gravity is not an issue) we can confidently predict that A will be faster than B because more available power means more power to overcome air resistance resulting in a higher average speed. On an undulating road however, power-to-weight ratio begins to matter more. If both cyclists weigh 80kgs, A will still be faster. But if A weighs 80kgs and B weighs 68kgs, cyclist A’s power-to-weight ratio is 3.13 watts/kg while B’s is 3.31 watt/kg.

On a flat road, there might not be much in it but head into the hills and it is cyclist B that will be pulling away! That’s because as the gradient increases, the relative contribution to the total energy required from overcoming gravity grows steadily. At the surface of the earth, gravity exerts a force on any mass of approximately 10 Newtons per kilo. A Newton of force applied through a distance of 1 metre requires a joule of energy. So if a rider weighs an extra 10kgs and climbs a hill that is 500m (1650ft) high, the simple laws of physics dictate that he or she will expend an extra 500 x 10 = 5000 joules of energy compared to a lighter cyclist.

 Understanding Power to Weight Ratio

  • Since power-to-weight ratio is determined by the simple formula power (watts) ÷ mass (kg), hopefully even the most non-mathematical readers can appreciate that there are 3 ways to increase your power-to-weight ratio:Increase your power output while keeping your weight constant;
  • Keep your power output constant while decreasing your weight;
  • Increase your power output while also decreasing your weight.

It also follows that if your power output increases but your weight increases too, your power-to-weight ratio might not improve at all. The same is true for cyclists who lose weight but suffer a drop off in maximum power – something we’ll return to.

Testing your own power output

Calculating your own power-to-weight ratio requires only two measurements: your weight and your maximum sustainable power output. The first is easy to measure – just hop on some accurate bathroom scales. The second requires a power output measurement. To do this, you’ll need to use a bike with a reliable power meter fitted (eg SRM, Powertap etc) or better still, a stationery bike with accurate power metering (eg WattBike) where you can pedal furiously without needing to slow down for bends, traffic etc.

To measure maximum sustainable aerobic power, ride gently for 10 minutes to make sure you’re thoroughly warmed up. Take a couple of minutes’ rest then ride as hard as you possibly can for 20 minutes and record your average power output figure in watts. This is your 20-minute maximum sustainable power output. Your 1-hour maximum sustainable power output will be around 5-10% lower (depending on fitness) than this figure – eg a 20-minute figure of 275 watts would equate to around 260 watts for an hour. Your 5-minute maximum power will be around 10% higher than the 20-minute figure – eg in this example, around 295 watts).

How good is good?

What constitutes a ‘good’ power-to-weight ratio? Well, this depends on the time period and the level at which you’re riding. Dr Andrew Coggan, an internationally acclaimed exercise physiologist has compiled some typical power-to-weight ratios(3), some of which are shown in table 2 below.

Table 2: Typical power-to-weight ratios for different level cyclists

Rider type

Power-to-weight ratio (watts/kg)

5 minutes

20 minutes

1 hour

Professional

7.0

6.1

6.0

Amateur

3.7

3.3

3.0

Recreational

2.5

2.1

1.8

It’s not surprising to observe that the pros have superior power-to-weight ratios regardless of time period. What’s more intriguing is that compared to amateur and recreation riders, the typical 1-hour power-to-weight ratio of a pro rider is only fractionally lower than the 20-minute figure. This is simply because a pro rider can ride at near maximum capacity with far less build up of muscle-fatiguing lactate than an amateur or recreational rider would experience.

Conclusion

Understanding the relationship between absolute power and power-to-weight ratio and the implications for cycling performance is vital for cyclists seeking maximum performance when heading for the hills. Regularly monitoring your sustainable power output and body mass should be considered part and parcel of tracking your progress. See the box below for a range of practical tips on how to improve your power-to-weight ratio.

Practical tips for improving power-to-weight ratio

We’ve seen that increasing power, reducing bodyweight or a combination of both can significantly improve your power-to-weight ratio. But how can you best achieve this? This will depend on your cycling background:

  • Relative beginners/novices – simply riding more miles will boost your power-to-weight ratio. Putting in more miles will not only boost your level of aerobic fitness (ie your sustainable power output), you’ll almost certainly lose a bit of excess body fat in the process. For example, if you drop from 86 to 82 kilos and increase your 20-minute power output from 210 to 235 watts, your power-to-weight ratio increases from 2.4 watts/kg to a very respectable 2.9 watts/kg.
  • Fitter and more experienced riders – need to be a bit more focussed than simply adding just more miles. Yes, more miles might result in reduced bodyweight, but add too much extra volume and you run the risk of fatigue and burnout. Moreover, an attempt to reduce weight when your body fat levels are already quite low can lead to muscle mass loss as well as fat loss. Given power is generated within muscle tissue, you might end up reducing your weight but losing some power with it, with the result that your power-to-weight ratio is barely improved. In fact, remembering that absolute power is still very important, you might be worse off overall. A better option is to include some specific training to boost maximal power output. This includes sessions such as intervals (long and shorter, more intense), hill repeats and some threshold rides. Because these sessions are quite demanding, make sure you build in sufficient recovery time into your weekly schedule – it’s during recovery that your muscles adapt and become more powerful!
  • Weight training – Another useful strategy, especially for more accomplished riders, is to perform some regular weight training. Studies have shown that performing heavy resistance training for the key cycling muscles (quadriceps, hamstrings, buttocks and calves) not only boosts muscle efficiency, it can help prevent the loss of muscle power during periods of high-volume training, or during periods of weight loss. The kind of training exercises that have produced good results in these studies include squats, leg press, hack squats and single leg press. The typical training weight used was around 6-8 rep max – ie enough weight to enable subjects to complete 6-8 reps but no more.
  • Nutrition – Regardless of your riding ability, consuming a healthy diet with a minimum of sugary, fatty and processed foods will play a part in improving power-to-weight ratio. All other things being equal, higher intakes of sugar and sugary foods in particular have been unequivocally linked with higher levels of body fat. Unlike muscle tissue, excess body fat blunts power-to-weight ratio and contributes nothing to power output! By the same token, a plentiful intake of dietary protein is recommended, especially after training. Protein is needed for recovery and repair after training and studies show that higher intakes of protein can help prevent muscle mass loss when training volumes are high. Studies show that whey protein is particularly well absorbed after training and that regular use of whey recovery drinks can help maintain/build power in endurance athletes.

Ref: peakendurancesport.com 

 

 

 
 
 
 
 



Leave your comment

* Required Fields

Registered in England No. 2164942